View ZHX1810MV115THTR_1339070.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ZHX1810
Slim Series SIR Transceiver
Product Specification
PS009318-1105
ZiLOG Worldwide Headquarters * 532 Race Street * San Jose, CA 95126-3432 Telephone: 408.558.8500 * Fax: 408.558.8300 * www.ZiLOG.com
This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters
532 Race Street San Jose, CA 95126-3432 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com
ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated.
Document Disclaimer
(c)2005 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights.
PS009318-1105
ZHX1810 Slim SIR Transceiver
iii
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDA LED Driver Anode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TXD Transmit Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RXD/Receive Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC Positive Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 3 3 3 3 3 3
Recommended Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical and Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Soldering and Cleaning Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . Reflow Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning (Preferred) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Packing, Storage, and Baking Recommendations . . . . . . . . . . . . . . . . . . . . . . Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Moisture-Proof Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 11 11 12 12 12 13
Taping Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Customer Feedback Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problem Description or Suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 18 18 18 18
PS009318-1105
Table of Contents
ZHX1810 Slim SIR Transceiver
iv
List of Figures
Slim SIR Transceiver Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 2 Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IF-Ie Characteristics (0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 IF-LEDA Characteristics (0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Directive Characteristics (Emitting) . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Directive Characteristics (Receiving) . . . . . . . . . . . . . . . . . . . . . . . . . 7 ZHX1810 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Alternative ZHX1810 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 9 Alternative ZHX1810 Mechanical Drawing . . . . . . . . . . . . . . . . . . . 10 ZHX1810 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ZHX1810 Reel Dimensions (Unit: mm) . . . . . . . . . . . . . . . . . . . . . . 14 ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 13. Alternative ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 14. Alternative ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12.
List of Tables
Table 1. Table 2. Table 3. Table 4. Pin Out for the ZHX1810 Transceiver . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 5 5
PS009318-1105
List of Figures and Tables
ZHX1810 Slim SIR Transceiver
1
Description
The ZILOG ZHX1810 is a low-profile version of ZiLOG's popular ZHX1010 1-meter transceiver. The transceiver is mechanically enhanced for ultra compact, power-conscious portable products, such as mobile phones, portable printers, handheld computers, and personal data assistants (PDAs). Designed to operate using the IrDA-Data mode, the transceiver combines an infrared emitting diode (IRED) emitter, a PIN photodiode detector, a digital AC coupled LED driver, and a receiver/decoder in a single package. The ZILOG ZHX1810 provides an efficient implementation of the SIR standard in a small-outline footprint format. Application circuit space is also minimized, as only three components are required. ZHX1810 also features an independently controlled shutdown that minimizes current draw to a maximum of 1 A.
Features * * * * * * * *
Compliant to IrDA Data Specification SIR Wide power supply voltage range, 2.4 to 5.5 V Minimum link distance, 1 M Low-power, listening current, 90 A (typical) at 3.0 V Slim form factor (9.1 mm long x 3.8 mm wide x 2.73 mm high) Only two external components required Extended operating temperature range (-30 C to +85 C) Meets IEC 825-1 Class 1 Eye Safety Specifications
PS009318-1105
ZHX1810 Slim SIR Transceiver
2
Block Diagram
Figure 1 is the block diagram for the Slim SIR transceiver.
Figure 1. Slim SIR Transceiver Block Diagram
Pin Descriptions
The ZHX1810 transceiver uses the pins listed in Table 1. The pins are described in this section.
Table 1. Pin Out for the ZHX1810 Transceiver Pin 1 2 3 4 5 6 -- Name LEDA TXD RXD SD VCC GND TAB Function IRED anode Transmitter input Receiver output Enables shutdown mode Supply voltage Ground Shield ground I/O -- I O I -- -- --
PS009318-1105
ZHX1810 Slim SIR Transceiver
3
LEDA LED Driver Anode
(Power) This output is connected to the LED anode. Current to the LED is sourced through an external resistor.
TXD Transmit Data
(Input, active high) This CMOS input is used to transmit serial data. This input has an internal pulldown resistor that is disabled (open-circuited) during shutdown.
RXD/Receive Data
(Output, active low) This output indicates received serial data. It is a tri-state, slew rate controlled CMOS output (tri-stated during shutdown) driver capable of driving a standard CMOS load. No external resistor is required.
SD Shutdown
(Input, active high) This input is used to place the integrated circuit into shutdown mode. Module shutdown current is influenced by the choice of capacitor used from VCC to ground.
VCC Positive Supply
(Power) Connect to positive power supply (2.4-5.5 V). Filter with a 0.33-F ceramic bypass capacitor and terminating resistor as close as possible to the VCC pin.
GND Ground
(Power) Connect to ground of the power supply. A solid ground plane is recommended for proper operation.
TAB
(Shield) The Shield tab must be soldered to the ground plane.
PS009318-1105
ZHX1810 Slim SIR Transceiver
4
Recommended Application Circuits
Figure 2 shows application block diagrams for the ZHX1810 transceiver.
Figure 2. Application Block Diagrams
PS009318-1105
ZHX1810 Slim SIR Transceiver
5
Electrical and Timing Specifications
Table 2 through Table 4 present the electrical and timing specifications for the ZHX1810 transceiver.
Table 2. Absolute Maximum Ratings Parameter Supply Voltage Input Voltage Output (External) Voltage LED Current Symbol Minimum Maximum Unit Comment Vcc VIN VOUT ILED -0.3 GND-0.3 GND-0.3 6.0 Vcc+0.3 Vcc+0.3 700 V V V mA Vcc, GND TxD, SD RxD 20% duty cycle, Ta=25 C, tON<90 S
Storage Temperature Solder Temperature ESD
TST TSOL
-40
100 240 1,000
C C V
Table 3. Recommended Operating Conditions Parameter Supply Voltage LED Voltage Ambient Operating Temperature Symbol Vcc VLED TOP Minimum 2.4 2.4 -30 Maximum 5.5 6.0 85 Unit V V C
Table 4. Electrical Characteristics Parameter High-Level Input Voltage Low-Level Input Voltage Low-Level Output Voltage Transmitter Current Listening Current Receive Current Symbol Condition VIH VIL VOL ILED ICC ICC 300 90 90 150 150 Min 0.6 Vcc -0.5 2.2 0.4 Typical Max Vcc+0.5 0.2 Vcc Unit V V V V mA Remarks TXD, SD TXD, SD RxD RxD
High-Level Output Voltage VOH
A A
Unless otherwise noted: Vcc=3.3 V, GND= 0 V, TA= 25 C
PS009318-1105
ZHX1810 Slim SIR Transceiver
6
Table 4. Electrical Characteristics (Continued) Parameter Standby Current Optical Rise/Fall Time RxD Pulse Width Power Shutdown Time Startup Time Receiver Latency Trans. Radiant Intensity Min. Threshold Irradiance Angle of Half Intensity Symbol Condition ISTB tRr, tRf tPWA TSD TSTU TL IE Eemin ILED=260 mA Vcc=3.3 V 40 2 20 40 20 3 870 100 100 3 SIR=115.2 Kbps 1.1 100 1.6 3.9 1 200 Min Typical Max 1 Unit Remarks SD=Vcc, TxD=0 V
A
nS
S S S s
mW/sr h,
v<(+15) h, v<(+15)
W/cm2
nS
Hor. and Vert. TxD="H"
Light Pulse Rise, Fall Time tor, tof Optical Pulse Width Optical Overshoot Peak Wavelength tOPW tOPO
S
% nm
P
Unless otherwise noted: Vcc=3.3 V, GND= 0 V, TA= 25 C
Figure 3 through Figure 6 show various electrical characteristics.
Figure 3. IF-Ie Characteristics (0)
PS009318-1105
ZHX1810 Slim SIR Transceiver
7
Figure 4. IF-LEDA Characteristics (0)
Figure 5. Directive Characteristics (Emitting)
Figure 6. Directive Characteristics (Receiving)
PS009318-1105
ZHX1810 Slim SIR Transceiver
8
Mechanical Drawings
In order to achieve the lowest possible costs and lead times, ZiLOG maintains multiple assembly facilities. The mechanical drawings for these transceivers are shown in Figure 7, Figure 8, and Figure 9. These devices, which show minor mechanical differences, are functionally equivalent in every way and meet all ZiLOG and IrDA standards and specifications. All ZHX1810 devices use the identical solder pad layout. Although reels are never mixed, ZiLOG reserves the right to ship from either facility in order to meet delivery requirements. When designing an IrDA subsystem, the user is advised to allow mechanical clearance for all versions of the IrDA transceiver.
Figure 7. ZHX1810 Mechanical Drawing
PS009318-1105
ZHX1810 Slim SIR Transceiver
9
Figure 8. Alternative ZHX1810 Mechanical Drawing
PS009318-1105
ZHX1810 Slim SIR Transceiver
10
Figure 9. Alternative ZHX1810 Mechanical Drawing
PS009318-1105
ZHX1810 Slim SIR Transceiver
11
Soldering and Cleaning Recommendations
Follow these recommendations to maintain the performance of the ZHX1810 transceiver.
Reflow Soldering
Note: Please refer to ZiLOG's Lead-Free Solder Reflow: Packaging Application Note (AN0161, http://www.zilog.com/docstools.asp) for more information about the solder profile.
Manual Soldering
* * * *
Use 63/37 or silver solder. Use a soldering iron of 25 W or smaller. Adjust the temperature of the soldering iron below 300 C. Finish soldering within 3 seconds. Handle only after ZHX1810 has cooled off.
Cleaning (Preferred)
Perform cleaning after soldering under the following conditions:
* * *
Cleaning agent: Alcohol Temperature and time: 30 seconds below 50 C or 3 minutes below 30 C Ultrasonic cleaning: Below 20 W
Additional cleaning methods can also be used. Please see the www.zilog.com documentation pages for details.
PS009318-1105
ZHX1810 Slim SIR Transceiver
12
Packing, Storage, and Baking Recommendations
Follow these recommendations to maintain the performance of the ZHX1810 transceiver.
Storage
To avoid moisture absorption, ZHX1810 reels must remain in the original, unopened moisture-proof packing. Parts must be soldered within 72 hours after unpacking. Reels that have been unpacked, but will not be soldered within 72 hours, must be stored in a desiccator.
Baking
Parts that have been stored over 12 months or unpacked over 72 hours must be baked under the following guidelines. Reels 60 C for 48 hours or more Loose Parts
* * *
100 C for 4 hours or more or 125 C for 2 hours or more or 150 C for 1 hour or more
PS009318-1105
ZHX1810 Slim SIR Transceiver
13
Moisture-Proof Packing
In order to avoid moisture absorption during transportation and storage, ZHX1810 reels are packed in aluminum envelopes (see Figure 10) that contain a desiccant with a humidity indicator. While this packaging is an impediment to moisture absorption, it is by no means absolute, and no warranty is implied. The user should store these parts in a controlled environment to prevent moisture entry. Please read the label on the aluminum bag for indicator instructions.
Figure 10. ZHX1810 Packaging
PS009318-1105
ZHX1810 Slim SIR Transceiver
14
Taping Specifications
Figure 11 shows the reel dimensions for the ZHX1810. Figure 12, Figure 13, and Figure 14 show the tape dimensions and configuration for the ZHX1810.
Figure 11. ZHX1810 Reel Dimensions (Unit: mm)
PS009318-1105
ZHX1810 Slim SIR Transceiver
15
Figure 12. ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 7
PS009318-1105
ZHX1810 Slim SIR Transceiver
16
Figure 13. Alternative ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 8
Figure 14. Alternative ZHX1810 Tape Dimensions and Configuration (Unit: mm) for Figure 9
PS009318-1105
ZHX1810 Slim SIR Transceiver
17
Ordering Information
To order ZHX1810, use ZiLOG part number ZHX1810MV115THTR. Notes: In order to ensure the lowest possible lead times, ZiLOG uses two different fab sources for the transceiver IC. Both of these ICs have been extensively tested and qualified to meet the ZHX1810 transceiver specifications. All ZiLOG devices are available lead free. Since 2005, ZHX1810 has been manufactured with lead-free components. When ordering from your ZiLOG distributor, there is a possibility that the parts containing lead might be shipped. To ensure that you receive lead-free devices, please use part number ZHX1810MV115TH2090TR. These devices meet or exceed RoHS Directive 2002/95/EC. For additional information, please see the ZiLOG Quality and Reliability web page at http://www.zilog.com/quality/index.asp.
PS009318-1105
ZHX1810 Slim SIR Transceiver
18
Customer Feedback Form
If you experience any problems while operating the ZHX1810 transceiver, or if you note any inaccuracies while reading this product specification, please copy and complete this form, then mail or fax it to ZiLOG (see "Return Information," below). We also welcome your suggestions!
Customer Information
Name Company Address City/State/Zip Country Phone Fax email
Product Information
Serial # or Board Fab #/Rev # Software Version Document Number Host Computer Description/Type
Return Information
ZiLOG System Test/Customer Support 532 Race Street San Jose, CA 95126-3432 Fax: (408) 558-8300 Web: www.zilog.com
Problem Description or Suggestion
Provide a complete description of the problem or your suggestion. If you are reporting a specific problem, include all steps leading up to the occurrence of the problem. Attach additional pages as necessary. _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________
PS009318-1105

▲Up To Search▲

Price & Availability of ZHX1810MV115THTR

	To Download ZHX1810MV115THTR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .